Audimax II   Floorstanding as in Hobby HiFi 2/2013

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 83 dB
  • size (HxWxD): 1590 x 220 x 404 mm
  • frequency range (-8dB): 23 - 30000 Hz
  • crossover frequency(s): 130, 2300 Hz
  • speaker type: bass reflex
Audimax 2 a huge floorstanding loudspeaker with drivers of high quality.

Audimax has been introduced in Hobby HiFi 3/2012. It is one of the best loudspeaker available for DIY. But it is really huge.

The new housing of Audimax II appears less weighty. It reaches very deep bass with passive radiators. The mids have cones made of ceramics with 80 mm voice coil. An air motion transformer Audaphon AMT-1i is used as tweeter.

The cabinet of Audimax II ist built of four single boxes, one placed on top of another.

The crossover consists of 2rd order high-pass and low-pass filters (12 dB per octave slope) .

The frequency response of this speaker a very linear. The decay spectrum is nearly perfect. At medium volume, i.e. 90 dB at 1 m, the nonlinear distortions are lower than 0.1%.

An excerpt from the Hobby HiFi review

An excerpt from the Hobby HiFi review

Our kit consists of

  • Audaphon AMT-1i
  • 2x Audaphon MB124T8
  • 2x Wavecor Subwoofer SW182BD02
  • 2x Wavecor PR182BD01 Passive Radiator
  • 5x Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • PE sealing tape, 5x2 mm
  • Damping Sonofil 100 x 35 cm for 20 litres
  • 2x Binding Post PK31, gold plated (per pair, red and black)
  • 8m Speaker cable 2x2.5 mm2, transparent
  • Pan screws 4x20 black, 24 pieces
  • Printed circuit board universal LP05, 150x115 mm, with brace
  • 2x Printed circuit board universal LP06, 220x155 mm, with brace
  • Plan for DIY kit

the crossover components (on the right),
to be mounted on a the PCBs.

  • Clarity Cap PX capacitor 2.7 μF / 250 Vdc
  • Clarity Cap PX capacitor 15 μF / 250 Vdc
  • Clarity Cap SA capacitor 5.6 μF / 630 Vdc
  • Clarity Cap SA capacitor 22 μF / 630 Vdc
  • electrolytic capacitor, etched 560 μF (in parallel:
    3x 150 uF, 100uF and 10 uF)
  • electrolytic capacitor, unetched, 68uF / 50 Vdc
  • 3x electrolytic capacitor, unetched, 100uF / 50 Vdc
  • Mundorf baked varnish air core coil BL71, 0.10 mH/0.23 Ohm
  • Mundorf baked varnish air core coil BL71, 0.47 mH/0.57 Ohm
  • Mundorf baked varnish air core coil BL71, 3.3 mH/1.75 Ohm
  • Mundorf baked varnish air core coil BL71, 18 mH/5.3 Ohm
  • Mundorf copper foil coil CFC14-0.68mH/0.20Ohm
  • Mundorf bs140 core coil 10mH/0,38Ohm
  • Metal-oxide resistor, 10W 2.2 Ohm (red-red-gold)
  • Metal-oxide resistor, 10W 2.7 Ohm (red-purple-gold)
  • 2x Metal-oxide resistor, 10W 3.3 Ohm (orange-orange-gold)
  • Metal-oxide resistor, 10W 4.7 Ohm (yellow-violet-gold)
  • Metal-oxide resistor, 10W 6.8 Ohm (blue-grey-gold)

Kit without cabinet, price per speaker   - not available

Kit with high-end crossover

Kit without cabinet, price per speaker   - not available (_)

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 16,30 excl. VAT: € 13.70 / $ 14.79

Home   Hobby HiFi Overview